SERIES O15
Solenoid Operators
For 2-Way and 3-Way O.E.M. applications. PeterPaul offers a complete line of miniature operators to control most media. Available up to 3/32" orifices. This line's unique design incorporates the coil and magnetic structure encapsulated completely in molded epoxy.
Choose your option
SERIES O20
Solenoid Operators
For 2-Way and 3-Way OEM applications. PeterPaul offers a complete line of operators to control most media. Available up to ¼" orifice.
Choose your option
SERIES O30
Solenoid Operators
For 2-Way and 3-Way OEM applications. PeterPaul offers a complete line of operators to control most media. Available up to 3/16" orifice.
Choose your option
SERIES O50
Solenoid Operators
For 2-Way and 3-Way OEM applications, PeterPaul offers a complete line of miniature operators to control most media. Available up to 1/8" orifice.
Choose your option
SERIES O58
Solenoid Operators
For two-way and three-way OEM applications, PeterPaul offers a complete line of low watt, miniature operators to control most media. Available up 1/8" orifice.
Choose your option
SERIES O70
Solenoid Operators
For 2-Way and 3-Way OEM applications, PeterPaul offers a complete line of large capacity operators to control most media. Available up 1/4" orifice.
Choose your option
SERIES OE20
Solenoid Operators
For 2-Way and 3-Way OEM application PeterPaul's unique, unitized design offers the advantages of simplicity of installation (unit is assembled and tested requiring no disassembly) common voltages and frequencies carry the U.L. and C.S.A. label. Approved for hazardous locations, Class I - Groups C and D (where atmosphere contains certain specific explosive gases). Class II - Group E (where atmosphere contains metallic dust), F (where atmosphere contains non-metallic combustible dust), and Group G (where atmosphere contains grain dust).
Choose your option
SERIES OE50
Solenoid Operators
For 2-Way and 3-Way OEM application PeterPaul's unique, unitized design offers the advantages of simplicity of installation (unit is assembled and tested requiring no disassembly) for common voltages and frequencies and carries the U.L. and C.S.A. label. Approved for hazardous locations, Class I - Group C and D (where atmosphere contains certain specific explosive gases). Class II - Group E (where atmosphere contains metallic dust), and Group G (where atmosphere contains grain dust).
Choose your option
SERIES OEH20
Solenoid Operators
For 2-Way Normally Closed applications where explosion-proof operators are required with high pressure ratings or inert seal requirement with bubble-tight sealing. Operator and precision press-in seat must be installed to factory specs.
Choose your option
SERIES OH20
Solenoid Operators
For 2-Way Normally Closed applications where high pressures are used - or where inert seals are required with bubble-tight sealing. Operator and precision press-in seat must be installed to factory specs. Consult factory for technical data and detail prints.
Choose your option
SJ BS Mod.B Series
Compact Design Screw Jacks
Ball screw jacks recommended for intermittent duty cycle (up to 70%)
Long life synthetic grease lubricated worm gear
High precision worm gearbox, ZI involute profile
Gearbox ratio from 1:4 to 1:36
Monobloc gearbox housing, robust and compact shape
Input speed up to 1.500 rpm
Ball screw drive, travelling nut (Model B)
SJ BS Mod.B Series Ball Screw Jacks with Travelling Nut:
11 sizes standard available
Ball screw from Ø 16 mm to Ø 140 mm
Load capacity from 5 kN to 800 kN
Choose your option
SJ Mod.A Series
Compact Design Screw Jacks
Acme screw jacks recommended for intermittent duty cycle
Long life synthetic grease lubricated worm gear
High precision worm gearbox, ZI involute profile
Gearbox ratio from 1:4 to 1:36
Monobloc gearbox housing, robust and compact shape
Input speed up to 1.500 rpm
Acme screw drive, travelling screw (Model A)
Acme screw 1- or 2-starts
SJ Mod.A Series Acme Screw Jacks with Travelling Screw:
14 sizes standard available
Acme screw from Ø 18 mm to Ø 160 mm
Load capacity from 5 kN to 1.000 kN
Choose your option
SJ Mod.B Series
Compact Design Screw Jacks
Acme screw jacks recommended for intermittent duty cycle
Long life synthetic grease lubricated worm gear
High precision worm gearbox, ZI involute profile
Gearbox ratio from 1:4 to 1:36
Monobloc gearbox housing, robust and compact shape
Input speed up to 1.500 rpm
Acme screw drive, travelling nut (Model B)
Acme screw 1- or 2-starts
SJ Mod.B Series Acme Screw Jacks with Travelling Nut:
14 sizes standard available
Acme screw from Ø 18 mm to Ø 160 mm
Load capacity from 5 kN to 1.000 kN
Choose your option
Solenoid Valves
Valve Technology
Valves are used to control the vacuum as well as the compressed air. The right valves can increase both the process reliability and the cost-effectiveness of the vacuum system.
Solenoid valves, which are controlled via electrical switch signals, are used for the control of compressed air or vacuum. These valves can be controlled directly as well as with pneumatic pilot operation.
Choose your option
Spring Plungers
Mounting Elements
Schmalz offers a wide range of mounting possibilities for integrating suction cups or special grippers into a vacuum system.
The spring plungers - components with versatile tasks: Compensate for overstrokes or height differences, soft touchdown, protect material/surface, etc.
Choose your option
Choose your option
Choose your option
Choose your option
Square / Circular / Rectangular Inflatable Jack
Inflatable jack, or lifting bag, is a pneumatic system made of elastomers or plastomers.
Filled with air, water or oil, these products are typically mounted in industrial automation systems to push, press, guide, clamp, lock, dampen, lift and handle.
Choose your option
Square Pancake® II
Interchangeable Compact Air Cylinders
Square Pancake II
Features
- Available in a wide range of sizes
- Standard: Seven bore sizes from ¾ to 2 inches and strokes to 4 inches
- SND Series: Four bore sizes from ¾ to 2 inches and strokes to 4 inches
- Self-lubricating composite body
- Clear anodized aluminum alloy heads
- Stainless steel tie bolts
- Rod Bushing
- Standard: composite
- SND Series: bronze
- Prelubed with Magnalube-G grease
- Chrome-plated stainless steel piston rods
- Rod end toolbar (SND Series)
- Air service to 200 psi
- Minimum Recommended Operating Pressure: 15 psi
- Temperature Ratings
- cylinder: -25° to +225° F (-32° to + 121° C)
- electronic sensors: -4° to +176° F (-20° to + 80° C)
- Internally lubricated Buna-N seals
- Many options available
- Magnetic piston sensing available
Technical Advantages
- Interchangeable composite cylinder barrel with stainless steel tie bolts and aluminum spacers that lock precision machined heads tightly into place.
- High-strength high performance composite resists corrosion, moisture and temperatures up to 325° F, while offering a high load capacity and very little friction.
- High impact resistance, minimizing failure caused by dings and dents.
- Self-lubricating cylinder wall ensures high performance thanks to a smooth interior with low coefficient of friction to minimize heat buildup, eliminate stick-slip and extend seal life.
- The hard chrome-plated stainless steel piston rod ensures long cylinder life.
- The high performance composite piston rod bearing and shaft work together to ensure high reliability: Over the cylinder’s cycle life, the composite bearing — which carries 60,000 psi — polishes the hard chrome-plated shaft.
- Magnalube G Teflon-impregnated grease provides a long operating life and lubricates across a wide temperature range.
- Buna-N O-rings are internally pre-lubed with Magnalube-G as standard. U-cup seals are also available.
Choose your option
Standard Inflatable Pipe Plug - OPL
The standard inflatable pipe plug (OPL) is designed to temporarily or permanently plug pipes, sewers or gutters. Flexible and light, it is effective for a fast, tight and reliable sealing of the pipe.
Many sizes are available to cover pipes from 30 to 2000 mm in diameter. Thanks to these various diameters, this plugging balloon can be used in many fields: sewage networks, rainwater and wastewater with the NR range, as well as hydrocarbons and/or chemicals with the NBR range.
Moreover, the standard inflatable pipe plug is available in standard or by-pass versions. Thanks to this adaptability, it is possible to safely carry out an application such as:
Choose your option
Suction Cups for Handling Composites
Vacuum Suction Cups
Suction cups and suction plates for handling flat, smooth workpieces such as glass which depend on high lateral forces. Bellow suction cups for gentle handling of, for example, automotive glass as well as handling of visible parts made of glass while leaving few marks.
These suction plates are ideal, in particular, for handling flexible materials such as prepreg or semi-finished products made of fiber composite material. The suction areas have uniform holes added for surface vacuum distribution. The adaptable sealing ring ensures a good seal and increases lateral forces.
Choose your option
Suction Cups for Handling Glass
Vacuum Suction Cups
Suction cups and suction plates for handling flat, smooth workpieces such as glass which depend on high lateral forces. Bellow suction cups for gentle handling of, for example, automotive glass as well as handling of visible parts made of glass while leaving few marks.
Choose your option
Suction Cups for Handling Sheet Metal
Vacuum Suction Cups
Schmalz product range includes a variety of suction cups with various shapes, sizes and materials, providing the right suction cup for every application. Suction cups consist of a elastomer part and a connection nipple. Please call if you require help making a selection.
Suction cups for handling sheet metal also with oily surfaces, handling blanks when unstacking as well as sheet metal parts with convex surfaces.
Choose your option
Suction Cups for Handling Wood
Vacuum Suction Cups
Schmalz product range includes a variety of suction cups with various shapes, sizes and materials, providing the right suction cup for every application. Suction cups consist of a elastomer part and a connection nipple. Please call if you require help making a selection.
Choose your option
Suction Cups for High-Temperature Applications
Vacuum Suction Cups
Suction cups and suction plates for handling flat, smooth workpieces such as glass which depend on high lateral forces. Bellow suction cups for gentle handling of, for example, automotive glass as well as handling of visible parts made of glass while leaving few marks.
Schmalz has developed suction cups to handle workpieces at high temperatures that are perfect for this task. The suction plates can withstand temperatures up to 600 °C and can be used for handling when tempering float glass and during the heat forming process of metal.
Choose your option
Suction Cups for Plastic Films and Paper
Vacuum Suction Cups
Schmalz product range includes a variety of suction cups with various shapes, sizes and materials, providing the right suction cup for every application. Suction cups consist of a elastomer part and a connection nipple. Please call if you require help making a selection.
Schmalz suction cups make for easy handling of foils and paper. The flat sealing lip and the reinforced inside of the cup prevent that the unstable workpiece gets sucked in. These sealing cups do not leave an imprint on the unstable workpieces even at high temperatures.
Choose your option
Suction Cups for the Electronics Industry
Vacuum Suction Cups
Schmalz product range includes a variety of suction cups with various shapes, sizes and materials, providing the right suction cup for every application. Suction cups consist of a elastomer part and a connection nipple. Please call if you require help making a selection.
The suction cups are suitable for handling printed circuit boards, blank circuit boards and other electronic components.
Choose your option
Suction Cups for the Packaging Industry
Vacuum Suction Cups
Schmalz product range includes a variety of suction cups with various shapes, sizes and materials, providing the right suction cup for every application. Suction cups consist of a elastomer part and a connection nipple. Please call if you require help making a selection.
These suction cups are characterized by a robust body and a soft sealing lip that molds to the shape of the packaging.