Choose your option
Choose your option
Choose your option
ATL and BSA Linearmech Series
Robust and Reliable Linear Actuators
Linearmech electromechanical linear actuators are easy-to-use and reliable products. Great and convenient alternative to the use of pneumatic cylinders recommended in case of medium to low speed application, intermittent duty cycle operation and self-locking requirement when load is applied, both pull or push load.
LINEARMECH ATL and BSA Series linear actuators are right angle design, AC or DC motor always included. Aluminum alloy housing with high resistance. Input drive with worm gear.
ATL Series Acme Screw Drive Linear Actuators:
5 standard sizes available
Acme screw from Ø 13,5 mm to Ø 18 mm
Linear speed up to 150 mm/s
Load capacity push-pull up to 11.000 N
Electric motors available: AC 3-phase or 1-phase motor, DC motors (12V, 24V)
Long life lubricated, maintenance free
BSA Series Ball Screw Drive Linear Actuators:
4 standard sizes available
Ball screw from Ø 14 mm to Ø 20 mm
Linear speed up to 125 mm/s
Load capacity push-pull up to 9.000 N
Electric motors available: AC 3-phase or 1-phase motor, DC motors (12V, 24V)
Long life lubricated, maintenance free
Choose your option
ATL and BSA Series
Right Angle Design Linear Actuators
Rear hinged attachments, 90° motor mounting design.
High precision worm gearbox, ZI involute profile.
Lubrication with synthetic grease (gearbox long life lubricated, screw drive regreasable).
ATL Series Acme Screw Drive Linear Actuators:
10 standard sizes available
Acme screw from Ø 13,5 mm to Ø 100 mm
Load capacity from 4 kN to 350 kN
Standard stroke length up to 800 mm, special stroke length also available upon request
BSA Series Ball Screw Drive Linear Actuators:
10 standard sizes available
Ball screw from Ø 14 mm to Ø 100 mm
Load capacity from 4 kN to 350 kN
Standard stroke length up to 800 mm, special stroke length also available upon request
Choose your option
B115 LF
LEAD FREE
LF SUPER BRONZE
Forged bronze ball valve with solder ends, full port.
• Pressure rating 600 WOG-150 WSP.
• Temperature range -4°F to 366°F.
• ANSI B16.18 connections.
• Made in specially formulated dezincification-resistant silicon bronze.
• SLT coated LF brass ball.
• Blow-out proof stem.
• PTFE seats and double O-ring packing.
• 100% electronically tested in the open and closed position at 80 psi.
• Valve to be used in fully open or fully closed position.
B115 LF: LEVER HANDLE - size 1/2” to 2”.
B125 LF: T- HANDLE - size 1/2” to 1”.
Choose your option
B11N LF
LEAD FREE
LF SUPER BRONZE
Forged bronze ball valve, FNPT threaded, full port.
• Pressure rating 600 WOG-150 WSP.
• Temperature range -4°F to 366°F.
• ANSI B16.18 connections.
• Made in specially formulated dezincification-resistant silicon bronze.
• SLT coated LF brass ball.
• Blow-out proof stem.
• PTFE seats and double O-ring packing.
• 100% electronically tested in the open and closed position at 80 psi.
• Valve to be used in fully open or fully closed position.
B11N LF: LEVER HANDLE - size 1/2” to 2”.
B12N LF: T- HANDLE - size 1/2” to 1”.
Choose your option
Ball Nuts DCN Series
Double Cylindrical Ball Nuts
BS Series Ball Screws:
Available on different accuracy grade (ISO IT3, IT5, IT7)
Nominal diameter d0 [mm], in accordance with standards ISO 3408 and DIN 69051:
14, 16, 20, 25, 32, 40, 50, 63, 80, 100, 120
Lead Ph [mm], in accordance with standards ISO 3408 and DIN 69051:
4, 5, 6, 8, 10, 12, 15, 16, 20,25, 32, 40
Max. thread length up to 10 m (depending on the diameters and the length of the bar)
DCN Series Double Cylindrical Ball Nuts:
Available with zero backlash or preloaded
Different dimensions available (DIN 69051, customer’s specs or SERVOMECH design)
Materials:
Threaded shafts: alloy steel 42CrMo4 or 50CrMo4 (UNI EN 10083-1), quenched
Hardness of ball tracks within the range (58 … 61) HRc
Ball nuts: alloy steel 18 NiCrMo5 (UNI EN 10084), case-hardened
Hardness of surfaces in contact within the range (58 … 61) HRc
Ball recirculating elements: alloy steel, case-hardened, with a surface hardness (50 … 55) HRc or plastic material depending on the application requirements
Choose your option
Ball Nuts DFN Series
Double Ball Nuts with Flange.
BS Series Ball Screws:
Available on different accuracy grade (ISO IT3, IT5, IT7)
Nominal diameter d0 [mm], in accordance with standards ISO 3408 and DIN 69051:
14, 16, 20, 25, 32, 40, 50, 63, 80, 100, 120
Lead Ph [mm], in accordance with standards ISO 3408 and DIN 69051:
4, 5, 6, 8, 10, 12, 15, 16, 20,25, 32, 40
Max. thread length up to 10 m (depending on the diameters and the length of the bar)
DFN Series Double Ball Nuts with Flange:
Available with zero backlash or preloaded
Different dimensions available (DIN 69051, customer’s specs or SERVOMECH design)
Materials:
Threaded shafts: alloy steel 42CrMo4 or 50CrMo4 (UNI EN 10083-1), quenched
Hardness of ball tracks within the range (58 … 61) HRc
Ball nuts: alloy steel 18 NiCrMo5 (UNI EN 10084), case-hardened
Hardness of surfaces in contact within the range (58 … 61) HRc
Ball recirculating elements: alloy steel, case-hardened, with a surface hardness (50 … 55) HRc or plastic material depending on the application requirements
Choose your option
Ball Nuts SCN Series
Single Cylindrical Ball Nuts
BS Series Ball Screws:
Available on different accuracy grade (ISO IT3, IT5, IT7)
Nominal diameter d0 [mm], in accordance with standards ISO 3408 and DIN 69051:
14, 16, 20, 25, 32, 40, 50, 63, 80, 100, 120
Lead Ph [mm], in accordance with standards ISO 3408 and DIN 69051:
4, 5, 6, 8, 10, 12, 15, 16, 20,25, 32, 40
Max. thread length up to 10 m (depending on the diameters and the length of the bar)
SCN Series Single Cylindrical Ball Nuts:
Available with zero backlash or preloaded
Different dimensions available (DIN 69051, customer’s specs or SERVOMECH design)
Materials:
Threaded shafts: alloy steel 42CrMo4 or 50CrMo4 (UNI EN 10083-1), quenched
Hardness of ball tracks within the range (58 … 61) HRc
Ball nuts: alloy steel 18 NiCrMo5 (UNI EN 10084), case-hardened
Hardness of surfaces in contact within the range (58 … 61) HRc
Ball recirculating elements: alloy steel, case-hardened, with a surface hardness (50 … 55) HRc or plastic material depending on the application requirements
Choose your option
Ball Nuts SFN Series
Single Ball Nuts with Flange
BS Series Ball Screws:
Available on different accuracy grade (ISO IT3, IT5, IT7)
Nominal diameter d0 [mm], in accordance with standards ISO 3408 and DIN 69051:
14, 16, 20, 25, 32, 40, 50, 63, 80, 100, 120
Lead Ph [mm], in accordance with standards ISO 3408 and DIN 69051:
4, 5, 6, 8, 10, 12, 15, 16, 20,25, 32, 40
Max. thread length up to 10 m (depending on the diameters and the length of the bar)
SFN Series Single Ball Nuts with Flange:
Available with zero backlash or preloaded
Different dimensions available (DIN 69051, customer’s specs or SERVOMECH design)
Materials:
Threaded shafts: alloy steel 42CrMo4 or 50CrMo4 (UNI EN 10083-1), quenched
Hardness of ball tracks within the range (58 … 61) HRc
Ball nuts: alloy steel 18 NiCrMo5 (UNI EN 10084), case-hardened
Hardness of surfaces in contact within the range (58 … 61) HRc
Ball recirculating elements: alloy steel, case-hardened, with a surface hardness (50 … 55) HRc or plastic material depending on the application requirements
Choose your option
BASE 40 TON - Aircraft Recovery Lift Bags
Aircraft Recovery Lift Bags
Model: BASE 40 T1
Aircraft Recovery Lift Bags (PARC) are used to lift disabled aircraft in accidents. Aircraft Recovery lift bags are a collection of different inflatable and independent chambers. These inflatable chambers allow any type of aircraft to be lifted without causing secondary damage.
Choose your option
BASE 60 TON - Aircraft Recovery Lift Bags
Aircraft Recovery Lift Bags
Model: BASE 60 T1
Aircraft Recovery Lift Bags (PARC) are used to lift disabled aircraft in accidents. Aircraft Recovery lift bags are a collection of different inflatable and independent chambers. These inflatable chambers allow any type of aircraft to be lifted without causing secondary damage.
Choose your option
Basic Ejectors
Vacuum Generators
Vacuum generators provide the required vacuum. The vacuum is generated either pneumatically (ejectors) or electrically (pumps, blowers).
Due to their small size, the basic ejectors can be used even in confined spaces. Due to the simple design with main body, venturi nozzle and silencer, this ejector is low maintenance and wear-resistant. The ejector's lightweight build makes it particularly suited for use in highly dynamic processes.
Choose your option
BE 11
Air Turbines / Air Motors / Drilling Spindles
High Precision Drilling Unit BE 11
BE11 precision drilling/grinding unit with a basic design based on a patented air-driven turbine motor. The drive unit is powered without intermediate gears and features variable speed control up to 80 000 rpm. A special high-speed precision bearing makes the drilling unit extremely quiet with a sound level of 67 dB (A). BE 11 / HFS 100 is designed for lubrication- free operation.
Choose your option
BE 21
Pneumatic Drilling Units With Feed
Air Operated Drilling Unit BE 21
The BE 21 is an air operated drilling unit with feed. The design of the BE 21 makes it very suitable for drilling blind holes, reaming etc. We also offer a stainless version of this unit, the BES 21, ideal for operation in environments where water or other corrosive fluids are present.
Choose your option
BE 22 SK
Air Turbines / Air Motors / Drilling Spindles
Pneumatic Drilling Unit BE 22 SK
The BE 22 SK consists of an air motor, a gear box and a body. The design is compact as well as robust. BE 22 SK comes in a wide range of speeds, and is available for lubrication-free operation.
Choose your option
BE 22 SKM
Milling Units
Pneumatic Milling Unit BE 22 SKM
The BE 22 SKM consists of an air motor, a gear box and a robust body. The design is compact as well as robust. BE 22/33 SKM comes in a wide range of speeds, and is available for lubrication- free operation.
Choose your option
BE 33
Pneumatic Drilling Units With Feed
Air Hydraulic Drilling Unit BE 33
The basic design of the BE 33 consists of a vane motor powered by compressed air, a pneumatic cylinder, and a closed hydraulic system. The total stroke length can be variably subdivided into rapid advance and working feed over the whole range. The throttle/check valve in the hydraulic system permits exact setting of the feed rate and high speed return.
Choose your option
BE 33 SK
Air Turbines / Air Motors / Drilling Spindles
Pneumatic Precision Drilling Unit BE 33 SK
The BE 33 SK consists of an air motor, a gear box and a body. The design is compact as well as robust. BE 33 SK comes in a wide range of speeds, and is available for lubrication-free operation.
Choose your option
BE 33 SKM
Milling Units
Pneumatic Milling Unit BE 33 SKM
The BE 33 SKM consists of an air motor, a gear box and a ro- bust body. The design is compact as well as robust. BE 22/33 SKM comes in a wide range of speeds, and is available for lubrication- free operation.
Choose your option
BE 48
Electro Pneumatic Drilling Units With Feed
Electro Pneumatic Drilling Unit BE 48
The BE 48-series is a flexible electro-pneumatic series of units in a modular design. The electric motor powers the spindle, while the feed is pneumatic. With the hydraulic feed control you can adjust the speed for best performance. The option linear sensor makes it possible to include functions such as multi- wall drilling and automatic chip removal. The series is available with integrated ER32 chuck as well as with multi-spindle heads.
Choose your option
BE(F) 22
Pneumatic Drilling Units With Feed
Air Hydraulic Drilling Unit BE(F) 22
The basic design of the BE(f) 22 consists of a vane motor powered by compressed air, a pneumatic cylinder, and a closed hydraulic system. The total stroke length can be variably subdivided into rapid advance and working feed across the whole range. The throttle/check valve in the hydraulic system permits exact setting of the feed rate and high speed return.
Choose your option
BE(F)P 22
Pneumatic Drilling Units With Feed
Air Hydraulic Precision Drilling Unit BE(F)P 22
The basic design of the BE(f)P 22 consists of a vane motor powered by compressed air, a pneumatic cylinder, and a closed hydraulic system. The BE(f)P 22 has a precision chuck for an extra high level of precision. Thanks to precision, separate and double ball bearings run-out amounts to a maximum of 0.01 mm. The total stroke length can be variably subdivided into rapid advance and working feed across the whole range . The throttle/check valve in the hydraulic system permits exact setting of the feed rate and high speed return.
Choose your option
BE(S) 21
Pneumatic Drilling Units With Feed
Air Operated Drilling Unit BE(S) 21
The BE 21 is an air operated drilling unit with feed. The design of the BE 21 makes it very suitable for drilling blind holes, reaming etc. We also offer a stainless version of this unit, the BES 21, ideal for operation in environments where water or other corrosive fluids are present.
Choose your option
BEG 48
Tapping Units
Electro Pneumatic Tapping Unit BEG 48
The BEG 48-series is a flexible electro-pneumatic unit in a modular design. The electric motor runs the spindle, while the feed is pneumatic. With the hydraulic feed control you can adjust feed rate in proportion to the pitch and the rpm. A tapping collect or a tapping spindle gives the unit the necessary length compensation. The series is available with JT2 taper or integrated ER32 chuck as well as with multi-spindle heads.
Choose your option
Bellows Suction Cups (Oval)
Vacuum Suction Cups
Schmalz product range includes a variety of suction cups with various shapes, sizes and materials, providing the right suction cup for every application. Suction cups consist of a elastomer part and a connection nipple. Please call if you require help making a selection.
Bellows suction cups with an oval shape are designed for long and narrow workpieces. Bellows suction cups are used if you need to handle workpieces with different heights, uneven surfaces or even fragile parts.
Choose your option
Bellows Suction Cups (Round)
Vacuum Suction Cups
Schmalz product range includes a variety of suction cups with various shapes, sizes and materials, providing the right suction cup for every application. Suction cups consist of a elastomer part and a connection nipple. Please call if you require help making a selection.
Bellows suction cups with a round shape are particularly suited for handling uneven and arched workpieces. Suction cups grip the workpiece fast and precisely due to their flat shape and small volume.
Choose your option
BEP 22 SK
Air Turbines / Air Motors / Drilling Spindles
Pneumatic Precision Drilling Unit BEP 22 SK
he BEP 22 SK is a precision drilling unit, equipped with a precision chuck. Thanks to separate and double ball bearings run-out amounts to a maximum of 0.01 mm. Its design is compact as well as robust. The BEP 22 SK comes in a wide range of speeds, and is available for lubrication-free operation.
Choose your option
BFVSTCE
BONOMI NORTH AMERICA
STAINLESS STEEL SANITARY BUTTERFLY VALVE
Stainless steel butterfly valve with EPDM seats and Sanitary Tri-Clamp Ends.
• AISI 316 L stainless steel.
• EPDM seat standard.
• Silicone or FKM (Viton) seats optional.
• Full port, sizes 1/2” to 8.”
• Sanitary Tri-Clamp Ends.
• Surface finish meets 3-A, FDA & USDA standards.
• 13-position, 304SS spring loaded lever lock handle 1/2” to 6”.
• 110 PSI @ 200°F.
BFVSTCE: size 1/2” to 8”.
Choose your option
BG MF H Series
Bevel Gearboxes
Bevel gearboxes with high performances and compact dimensions. Suitable for operation at high input speed, up to 3000 rpm, with low noise level and high efficiency. Modular system with different versions available, additional outputs up to 6 shafts.
Bevel gears are made in high quality alloy steel, cut according to GLEASON spiroidal toothing system, casehardened, tempered and lapped in pairs. The accurate and consolidated manufacturing technology allows to produce bevel gears able to work with low noise level and with high efficiency.
BG MF H Series Input with IEC Motor Flange and Output with Hollow Shaft:
6 standard sizes available
Ratio from 1:1 to 1:4
Cubic shaped housing with 6 machined sides, each of them with 4 mounting threaded holes
Covers and shaft hubs machined with centring diameter with outward tolerance f7
Features:
Output shaft angular backlash: max. 10 arcmin (standard); on request controlled and reduced backlash,
averagely less than (5 … 6) arcmin.
Tapered roller bearings standard on all solid shafts and hollow output shaft;
ball bearings on hollow input shafts for motor flange execution.
Long-life grease lubrication for applications with low input speed.
Synthetic oil lubrication on request and in case of high input speed.
Assembling carried out entirely inside the company SERVOMECH, following all procedure steps to ensure a precise adjustment of the bearings and of the bevel gears to exalt following performances:
– noiseless operation
– high efficiency
– long service life
Choose your option
BG MF M1/S1/R1 Series
Bevel Gearboxes
Bevel gearboxes with high performances and compact dimensions. Suitable for operation at high input speed, up to 3000 rpm, with low noise level and high efficiency. Modular system with different versions available, additional outputs up to 6 shafts.
Bevel gears are made in high quality alloy steel, cut according to GLEASON spiroidal toothing system, casehardened, tempered and lapped in pairs. The accurate and consolidated manufacturing technology allows to produce bevel gears able to work with low noise level and with high efficiency.
BG MF M1/S1/R1 Series Input with IEC Motor Flange and Output with Solid Shaft:
6 standard sizes available
Ratio from 1:1 to 1:4
Cubic shaped housing with 6 machined sides, each of them with 4 mounting threaded holes
Covers and shaft hubs machined with centring diameter with outward tolerance f7
Features:
Output shaft angular backlash: max. 10 arcmin (standard); on request controlled and reduced backlash,
averagely less than (5 … 6) arcmin.
Tapered roller bearings standard on all solid shafts and hollow output shaft;
ball bearings on hollow input shafts for motor flange execution.
Long-life grease lubrication for applications with low input speed.
Synthetic oil lubrication on request and in case of high input speed.
Assembling carried out entirely inside the company SERVOMECH, following all procedure steps to ensure a precise adjustment of the bearings and of the bevel gears to exalt following performances:
– noiseless operation
– high efficiency
– long service life
Choose your option
BG S H Series
Bevel Gearboxes
Bevel gearboxes with high performances and compact dimensions. Suitable for operation at high input speed, up to 3000 rpm, with low noise level and high efficiency. Modular system with different versions available, additional outputs up to 6 shafts.
Bevel gears are made in high quality alloy steel, cut according to GLEASON spiroidal toothing system, casehardened, tempered and lapped in pairs. The accurate and consolidated manufacturing technology allows to produce bevel gears able to work with low noise level and with high efficiency.
BG S H Series Input with Solid Shaft and Output with Hollow Shaft:
6 standard sizes available
Ratio from 1:1 to 1:4
Cubic shaped housing with 6 machined sides, each of them with 4 mounting threaded holes
Covers and shaft hubs machined with centring diameter with outward tolerance f7
Features:
Output shaft angular backlash: max. 10 arcmin (standard); on request controlled and reduced backlash,
averagely less than (5 … 6) arcmin.
Tapered roller bearings standard on all solid shafts and hollow output shaft;
ball bearings on hollow input shafts for motor flange execution.
Long-life grease lubrication for applications with low input speed.
Synthetic oil lubrication on request and in case of high input speed.
Assembling carried out entirely inside the company SERVOMECH, following all procedure steps to ensure a precise adjustment of the bearings and of the bevel gears to exalt following performances:
– noiseless operation
– high efficiency
– long service life
Choose your option
BG S/R M/S/R Series
Bevel Gearboxes
Bevel gearboxes with high performances and compact dimensions. Suitable for operation at high input speed, up to 3000 rpm, with low noise level and high efficiency. Modular system with different versions available, additional outputs up to 6 shafts.
Bevel gears are made in high quality alloy steel, cut according to GLEASON spiroidal toothing system, casehardened, tempered and lapped in pairs. The accurate and consolidated manufacturing technology allows to produce bevel gears able to work with low noise level and with high efficiency.
BG S/R M/S/R Series Input and Output with Solid Shaft, Standard or Large Diameter:
6 standard sizes available
Ratio from 1:1 to 1:4
Cubic shaped housing with 6 machined sides, each of them with 4 mounting threaded holes.
Covers and shaft hubs machined with centering diameter with outward tolerance f7
Features:
Output shaft angular backlash: max. 10 arcmin (standard); on request controlled and reduced backlash,
averagely less than (5 … 6) arcmin.
Tapered roller bearings standard on all solid shafts and hollow output shaft;
ball bearings on hollow input shafts for motor flange execution.
Long-life grease lubrication for applications with low input speed.
Synthetic oil lubrication on request and in case of high input speed.
Assembling carried out entirely inside the company SERVOMECH, following all procedure steps to ensure a precise adjustment of the bearings and of the bevel gears to exalt following performances:
– noiseless operation
– high efficiency
– long service life
Choose your option
Bin Picker SBPG
Area Gripping Systems and End Effectors
Area gripping systems and end effectors are gripping systems that can be attached directly on the robot.
Ready-to-connect vacuum gripper for automated bin picking
Choose your option
Bleed Feed Valves
A Bleed/Feed valve acts as a 3-way, 3-position, closed center control valve, with two solenoid operators. As you can see from the pictures to the right, the Bleed/Feed valve is essentially two DASH 1 valves that have been mounted together with special porting, depending on customer requirements.